Product ID:DURA-POXY SEMI-GLOSS ACRYLIC ENAMEL 1685 SERIES/ALL COLORS
MSDS Date:09/12/1994
FSC:8010
NIIN:00F026084
Status Code:A
MSDS Number: CJZRW

KELLY-MOORE PAINT CO INC

1015 COMMERCIAL ST
SAN CARLOS, CA 94070
US

Emergency Phone: 415-592-8337

Info Phone: 415-592-8337

Preparer: M SCHEFER

Cage: 0Y837

KELLY-MOORE PAINT CO INC

SAN CARLOS, CA 94070 US

Telephone: 650-592-8337

Cage: 0Y837

DIETHYLENE GLYCOL BUTYL ETHER

CAS: 112-34-5

RTECS: KJ9100000

DIETHYLENE GLYCOL METHYL ETHER

CAS: 111-77-3

RTECS: KL6125000

TEXANOL

CAS: 25265-77-4

RTECS: UF6000000

HEXYLENE GLYCOL

CAS: 107-41-5

RTECS: SA0810000

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION: IRRITATION TO UPPER
RESPIRATORY TRACT. SKIN/EYES: MAY CAUSE IRRITATION.
Effects of Overexposure:DIZZINESS, HEADACHE, NAUSEA, CONFUSION,
IRRITATION, UNCONSCIOUSNESS
Medical Cond Aggravated by Exposure:SEE YOUR PHYSICIAN FOR SPECIFIC
MEDICAL OPINION REGARDING YOUR CONDITION.

First Aid:INHALATION: REMOVE TO FRESH AIR. RESTORE BREATHING. EYES:
FLUSH W/LARGE VOLUMES OF WATER FOR AT LEAST 15 MINS. SKIN: WIPE OFF
W/RAG. WASH THOROUGHLY W/SOAP & WATER. OBTAIN MEDICAL ATTENTION IN
ALL CA SES.

Flash Point:NONE
Fire Fighting Procedures:NONE
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE (DUE TO
BUILD UP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.

Spill Release Procedures:VENTILATE AREA TO PREVENT BUILD-UP OF VAPORS.
FOR SMALL SPILLS: SOAK UP W/ABSORBENT. FOR LARGER SPILLS: DIKE AREA
W/ABSORBENT MATERIAL & SCOOP UP LIQUIDS.

Handling and Storage Precautions:STORE UPRIGHT IN SEALED CONTAINERS
AWAY FROM HEAT & FLAME.
Other Precautions:AVOID CONTACT W/SKIN/EYES & CLOTHES. AVOID BREATHING
SPRAY MIST/ DUST.

Respiratory Protection:USE A PARTICLE MASK NIOSH/MSHA IF LOCAL
VENTILATION IS INADEQUATE. IF LOCAL VENTILATION IS NOT
SUFFICIENT/WHERE EXPOSURE LIMITS ARE EXCEEDED, WEAR A SUITABLE,
PROPERLY FITTED RESPIRATOR NIOSH/MSHA TC- 23C/BETTER FOR ORGANIC
VAPORS W/A DUST FILTER AS NEEDED.
Ventilation:LOCAL CROSS VENTILATION/MECHANICAL EXHAUST SUFFICIENT TO
KEEP ALL HAZARDOUS VAPOR CONCENTRATIONS BELOW PRESCRIBED LIMITS.
Protective Gloves:RECOMMENDED
Eye Protection:GLASSES W/SIDE SHIELDS/GOGGLES ARE RECOMMENDED
Work Hygienic Practices:REMOVE & WASH CONTAMINATED CLOTHES BEFORE
REUSE. WASH HANDS THOROUGHLY AFTER HANDLING.
Supplemental Safety and Health
PRODUCT MAY CONTAIN TITANIUM DIOXIDE/SILICATES THAT MAY BE NUISANCE
DUST HAZARDS IN THEIR ORIGINAL DRY POWDER FORM BUT ARE NOT
HAZARDOUS IN WET PAINT.

Boiling Pt:B.P. Text:212F
Vapor Density:<1
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:65-71

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS
Stability Condition to Avoid:HEAT, FLAME
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED TO DECOMPOSITION AS IN WELDING.

Waste Disposal Methods:DISCARD IN LAND FILL IN SEALED METAL CONTAINERS
AWAY FROM HEAT & FLAME. DISPOSE OF IN ACCORDANCE W/LOCAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.